Yes, GlazeGuard is a tough water based polyurethane sealer developed specifically to bond to ceramic and porcelain tile. Not many sealers can bond (long term) to ceramic or porcelain tile. However, GlazeGuard does! We use propriety adhesion promoters and the latest nano technology to enable GlazeGuard to do this.

The kit consists of 1 bottle of A side solution, and 1 bottle of B side solution. A total of 2 bottles in a kit. Cleaning products and application equipment are not included.

Apply using a roller, in a similar manner to painting a floor. For best results use a high quality 3/8 nap microfiber non-shed roller.  To cut in the edges and around corners use a 4” or 6” wide roller or brush. For large areas it is recommend that two people apply the product. One person cutting in the edges and corners and the other rolling out the main area. Make sure the room is well lit. This will help avoid missed spots when applying a clear sealer. GlazeGuard is a two-part material, so once mixed  it has 60-minute working time (pot life). Only mix enough material that can be used in 60 minutes. Change out rollers after 60 minutes of use.  Do not allow GlazeGuard sealer to puddle in the grout joints.

Both the gloss and the satin finish will give you a wet look. The gloss is a high gloss finish and the satin is a semigloss finish. Both will bring out the colors of tile. The Matte finish will leave the tile with a flat no sheen finish. Note that with all three finishes (Gloss, Matte and Satin) will darken the grout. To get an idea of how dark the grout line will become, just sprinkle some water on to your grout joint and observe how dark it turns. The GlazeGuard will produce a similar effect but the grout will stay that dark we it dries.

Yes, GlazeGuard is fully compatible with most grout colorant (acrylic and epoxy grout color). Follow grout colorant manufactures instruction regarding dry time. The grout colorant must be dry before sealing over with GlazeGuard.

GlazeGuard when fully cured has a hard surface so dirt does not easily stick to it. You don’t need to use aggressive cleaners. A part of maintaining your floor is to use dust mop or “Swiffer” type microfiber mop to keep sand and dirt off the floor. After that to wash the floor you can use neutral clean or mild liquid detergents, light vinegar solutions, or light ammonia solutions. Stay away from solvents like Paint strippers, Acetone and Xylene. If you do have to use concentrated cleaners/degreasers. Dilute according to manufactures directions and clean up residue right away. For more information see GlazeGuard Maintenance instructions.

Yes. We typically ship by DHL or UPS outside the USA. Our products are non-hazard and ship easily by land, ocean or air. You just have to pay the shipping cost including any local taxes or duties that may apply. If you contact service@covertecproducts.com and confirm product quantity and your ship to address, we would be happy to quote.

For wet areas such as shower room floors and restrooms that regularly get wet, we recommend that you first prepare the surface with PreTreat before coating with GlazeGuard. PreTreat is a mild acid-based cleaner that will microscopically etch the tile surface and increase the adhesion.

Yes, GlazeGuard can be used to seal wet areas such shower room floors and walls. Before sealing the tile as to be lightly etch using our PreTreat ( or PreTreat Gel for the walls) to give better adhesion under wet conditions. Wash the floor with our neutral cleaner GlossClean to neutralize the surface and allow tile and grout to dry before sealing.

Yes. Because GlazeGuard contains adhesion promoters it can bond to may surfaces including concrete, wood, natural stone terrazzo, metal, vinyl and rubber.

GlazeGuard is not recommended for polished surfaces such as polished porcelain or polished marble.

Yes, GlazeGuard is a UV resistant non yellowing polyurethane coating and can be used for exterior and interior applications. Exterior surfaces should be prepared using PreTreat before applying the GlazeGuard.

Yes, GlazeGuard will form a clear stain and oil resistant barrier across the surface of the tile and grout. GlazeGuard can drip and form runs, so for vertical applications, the product needs to be applied in two thin coats. Wait approximately 5 minutes between coats and back roll as necessary to catch any runs.

We have many customers using GlazeGuard to provide a clear protective surface to porcelain tile and grout. It will give the floor a long-lasting gloss, satin or matte appearance and make the tile and grout much easier to clean . GlazeGuard typically lasts 3 years in high traffic (commercial) applications and typically 5 years in a residential application. When it comes time to topcoat GlazeGuard, you just lightly sand the surface and clean off the dust then reapply a topcoat.
The 1-gallon kit of Gloss or Satin finish will cover approximately 500 sq. ft (46 sq.m)
The 1-quart kit of Gloss or Satin will cover approximately 125 sq. ft (12 sq.m)
The 0.75-gallon kit of Matte finish will cover approximately 375 sq. ft (35 sq.m)
The 36 oz kit of Matte will cover approximately 140 sq. ft (13 sq.m)
Note that coverage depends on the texture of the surface and the size and porosity of the grout lines. Tile floors with wider grout lines will use more material per gallon.
A single coat is usually enough for GlazeGuard. If you need a second coat, then sand 1st coat to a dull finish using 220 grit paper. Clean up with rubbing alcohol and cloth to remove the dust. Allow to dry and apply GlazeGuard.
No. Typical grout sealers are water repellant and not compatible with GlazeGuard. They will act as a bond breaker. GlazeGuard on its own will provide a clear protective surface to both the tile and grout. It will give the floor a long-lasting wet look appearance and make the tile and grout much easier to clean.
To spot repair or recoat entire area it is not necessary to strip the sealer, you just need to sand or scrub the surface clean so it can be top coated. Sand with 120 grit sandpaper or scrub with black pad and GlossClean neutral cleaner. Clean off the dust or residue and apply a topcoat. For more detailed instruction see GlazeGuard Maintenance instructions.
Light foot traffic is possible after 10-12 hours and heavy foot traffic is possible after 24 hours at 77deg F (25 deg C) and 50% humidity. Dry time is very dependent product thickness, temperature and humidity. The higher the temperature and humidity the faster it will dry. If the tile is cold and the air is dry the dry time will be significantly extended. Allow a further 24- 48 hours before moving furniture (Lift and place).
Yes. You are going to apply a sealer that will last many years. It is important to make sure that any dirt, footprints, hair and dust off the floor before you seal with GlazeGuard.
We recommend our CT_50 tile and grout cleaner. This powerful surface cleaner will clean off oil, grease, wax, soap scum, mold, dirt and stains from glaze and unglazed tile, grout, natural stone and concrete surfaces.
GlazeGuard has good anti slip properties when dry but it can get slippery when wet on a smooth surface. Increase slip resistance can be achieved by mixing in our CoverGrip anti slip additive at the time of application.
No. GlazeGuard is not recommended for porcelain tubs and sinks.
Yes, the pot life is very important. The pot life is basically the amount of working time you have to apply the product once the product is mixed. GlazeGuard has a 60-minute pot life at 77deg F (25 deg C). Any remaining product after that point must be thrown away. Using product once in its past its pot life will result in product failure.

GlazeGuard has some flexibility and will provide a clear protective seal to ceramic tile and grout. However, GlazeGuard will not bridge moving cracks in the grout. These will need to be fixed first. The floor to wall transition should be sealed using polyurethane or acrylic caulk.

For additional slip resistance when wet, we have a fine additive called CoverGrip which is mixed into the GlazeGuard during application. This will give the surface a high traction finish.