skip to Main Content

PrimeSeal Fast Drying WB Primer and Sealer

$32.75$103.00

Shipping: FREE on all orders in the continental US
Delivery: Typically 2 to 3 business days
Clear

Location

Interior

Task

Floors

Application

3/8” (10 mm) nap mohair roller, brush or airless spray.

Surface

Vinyl, Terrazzo, Concrete, and other hard surfaces

Base

Water Based

Drytime

45-60 min

Coverage

1500 to 1800 ft²/gal

Finish

Clear

PrimeSeal Gloss Fast Drying, Water-Based Primer And Sealer Coating

A fast drying primer and sealer clear coat for vinyl and stone tile surfaces.

Application

Micro Fiber Flat Mop, T-bar Applicator, Roller.

Coverage

1500-1800 sq.ft/gal/coat

Dry Time

20 -30 minutes

Heavy Traffic

2 hours

Surface

Vinyl Tile (VCT), Epoxy and Cement Terrazzo, Slate, Concrete, Linoleum, Vinyl Plank.

For interior use only.

FREE SHIPPING FOR ALL ORDERS IN THE CONTINENTAL USA!

Are you a contractor? Contact us for a special offer.

Frequently Asked Questions

What is PrimeSeal?

What is PrimeSeal?

PrimeSeal is fast drying clear sealer and prime coat. When applied to porous vinyl tile (VCT), stone and interior concrete the product will produce a semi-permanent primer prior to applying topcoats. It can also be used as a sealer / barrier coat to protect the floor surface from dirt and water penetration.

How Do I have to prepare the surface?

Pre-sweep or dust mop all areas and remove gum, tar, glue, etc. from the floor. Apply FloorStrip HP floor finish stripper. Allow time for the stripper to begin to breakdown oils and soiling. Scrub away the old wax, stains, and ground in soiling with the appropriate stripping pad or brush and scrubber. Extract and rinse away or wipe up the stripper residue. Allow the floor to dry for 4 hours. Circulate air during this drying process using a fan air blower. The floor must be cleaned and rinsed thoroughly to ensure that it is pH neutral. Make sure substrate is dry before application. Use a microfiber mop to pick up all dust and dirt.

Is it important I use this first before using the top coating?

We strongly recommend this primer after stripping off floor finish especially on vinyl tile rubber flooring and porous stone.  It will fill the microscopic spaces in the tile or stone and create and even and less absorbent based for the topcoat. This will result in a much more uniform topcoat finish.

What surfaces do I use it on?

Any porous surface especially after the existing finish has been stripped such as Vinyl Tile VCT, Luxury LVT, Sheet Vinyl, Linoleum, Travertine, Concrete floors, Terrazzo, Natural Stone,  and Mexican Tile.  Note PrimeSeal is for interior use only.

Do I have to mix this product?

Stir the container for 1 minute to make sure all contents evenly dispersed. This product is an RTU product, Ready To Use.

What is the coverage of the product?

1500-1800 sq. ft/gal (36.7-44.0 sq. m/l) A two coat application is recommended for porous substrates.

How do I apply the product?

PrimeSeal may be applied by, flat micro-fiber mop head, or clean synthetic mop and bucket. Saturate the mop and apply 1st coat at a rate of 1500 to 1800 sq. ft per gallon. DO NOT OVER-APPLY. This product should be applied thinly and evenly. Allow the 1st coat to completely dry usually 20 to 45 minutes depending on temperature and air flow. Apply 2nd coat a rate of 1500 to 1800 sq. ft per gallon and allow to dry tack free (a minimum of 20 minutes) before applying any topcoat.

PrimeSeal Photos

PrimeSeal Videos

Back To Top